Voor u, als watersporter, bieden wij bovendien een extra voordeel: de boord-PC kan worden voorzien van het gebruiksvriendelijke en uitgebreide navigatieprogramma ORBIT-Commander bavigatieprogramma voor een meerprijs van slechts € 65,00 (normaal  €  95.00)
Dit programma is uitgerust met de nieuwste vaarkaarten van de Nederlandse en Belgische (Vlaanderen) doorgaande vaarwateren. Deze kaarten kunnen onbeperkt, en zonder dat een internetverbinding nodig is, blijvend worden gebruikt. Jaarlijks verschijnen er wèl updates tegen zeer schappelijke prijzen, zodat u ze, indien gewenst, bijgewerkt kunt houden. Ook zijn er voor dit programma kaartensets leverbaar van alle belangrijke binnen- en buitenwaterkaarten van Europa en daarbuiten. Advies: schaf voor de Nederlandse Wadden deze combinatieset van papieren en digitale kaarten voor extra veiligheid en digitaal regelmatig (gratis)  bijgewerkte kaarten aan (complete set iclusief installatie  €   59.00 = indien meteen meebesteld).

Behalve GPS en AIS kunt u met dit programma ook boordapparatuur - zoals bijvoorbeeld een stuurautomaat - aansluiten. 
Als u dit navigatie programma samen met de laptop bestelt, bespaart u € 30.00 op het programma ORBIT-Commander en € 50,00 op de installatiekosten. 

Ook kunt u, in plaats hiervan, kiezen om de laptop te laten installeren met het programma PC-Navigo Nederland versie 2023 voor  €  250,00.
Pc-Navigo is ook leverbaar in de uitvoeringen:

BENELUX 2023  -  €  349,00
en
EUROPA 2023  -  €  499,00

PC-Navigo is hèt programma waar de beroepsvaart op vertrouwt als het gaat om nauwkeurige routeberekeningen met de nieuwste stremmingsgegevens en stromingsinvloeden.

Ook WinGPS5(6)  is een uitstekende keuze: 

Vooral voor watersporters op buitenwater heeft dit programma een zeer uitgebreide digitale kaartcollectie en voor regatta zeilers zelfs een speciaal ontwikkeld programma.

WinGPS5(6) is er in verschillende uitvoeringen:

- van een gratis testprogramma voor computer of tablet tot de meest uitgebreide informatie voor regattazeilers. Dit gecombineerd met gunstig geprijsde digitale kaarten maakt het tot een ijzersterke keuze.

- WinGPS5 Lite

- WinGPS Navigator

- WinGPS5(6) PRO

- WinGPS5(6) Voyager

U kunt ook meerdere navigatieprogramma's NAAST elkaar laten plaatsen en deze alle voorzien van dezelfde GPS en/of AIS aansluiting.

Heeft u nog geen GPS dan kunt u bij ons een zeer precieze en betrouwbare, waterproof, schokvaste, voorzien van Waas/Egnos (voor extra hoge preciesie) aanschaffen voor € 65,00.

Ook andere navigatieprogramma's - zoals bijvoorbeeld WinGPS5 in de diverse uitvoeringen - zijn leverbaar, alsmede (waterproof) 12 Volt beeldschermen, AIS apparatuur, papieren en digitale kaarten van alle vaarwateren in de wereld, enz.
Kijk hiervoor in onze webshop bij de betreffende rubrieken.

U kunt uw bestelling het beste per e-mail of telefoon opgeven zodat de verschillende mogelijkheden met u nader kunnen worden doorgenomen. Ook kunt u in de webshop (shop.b-bit.nl) nadere informatie over de verschillende producten bekijken en aan de hand hiervan uw bestelling samenstellen. Bij de opties kunt u uw componenten kiezen. U kunt meerdere keren een keuze aanklikken. Dit wordt dan bij elkaar opgeteld weergegeven. U ontvangt van ons altijd eerst een besteloverzicht met eventuele nadere informatie over levertijd, beschikbaarheid en betalings- en verzendmogelijkheden en indien van toepassing prijswijzigingen. U kunt dan deze gegevens aanpassen, of bevestigen dat de bestelling zo kan worden uitgevoerd. Daarna ontvangt u onze orderbevestiging.

ARTIKELNUMMER:  SunPc-ET20V5

S P E C I F I C A T I E S  van de uitvoering met de Intel i5 processor:

Fanless and Silent

Passive cooling, no fan noise at all

Perfect to be used in noise-sensitive environments

Fanless, dust-free and thus virtually maintenance-free

Low Power Consumption

Power consumption in idle mode with 2.5" SSD under Windows 10: ca. 6 W only

24/7 Nonstop Operation

This device is approved for 24/7 permanent operation.

Requirements:

- Free circulation of air amongst the PC must be guaranteed.

- Ventilation holes must stay clear.

- If a hard disk is installed, this must also be approved for permanent operation by its manufacturer

Chassis

Slim-PC with black steel chassis

Without cooling fan, passive cooling only

The bays for memory, 2.5" drive and M.2 card

can easily be accessed by removing two cover plates.

Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres

Weight: 1.5 kg net and 2.2 kg gross

Two holes for Kensington Lock and numerous 

threaded holes (M3) at both sides of the chassis

Operating Position

1) Vertical: Usual operating position with the supplied feet (DisplayPort output facing up).

2) VESA-mounted: The device can also be mounted behind an appropriate monitor using the supplied VESA mount kit.

Note: From a thermal point of view horizontal operation is permitted. However, there are no rubber feet on the device. The maximum operating temperature is 35 °C then.

Operating System

This barebone system comes without operating system.

It is compatible with Windows 10/11 (64-bit) and Linux (64-bit).

Processor

Model: Intel Core i5-10210U (ULV)

System-on-a-chip architecture (SoC) with integrated memory and graphics controller

FCBGA1528 package - directly soldered onto the mainboard

Code name: Comet Lake U (10th Generation Intel Core)

Cores / Threads: 4 / 8

Base frequency: 1.6 GHz

Max. Turbo frequency: 4.2 GHz

Intel Smart Cache: 6 MB

TDP wattage: 15 W maximum

Manufacturing process: 14nm

Maximum Tjunction Temperature: 100 °C

Supports 64-bit, VT-x (EPT), VT-d, Enhanced SpeedStep, NX bit, AES-NI, SSE 4.1/4.2

Integrated Graphics

Intel UHD Graphics

GPU clock frequency: 300~1100 MHz

Execution Units (EUs): 24

Supports DirectX 12, OpenGL 4.5

Supports full H264, H265 8/10 bit, VP8/9, VC-1, AVC hardware decoding

Supports Quick Sync Video and Clear Video HD technology

Supports up to three independent screens:

1) DisplayPort 1.2 supports Ultra HD @ 60 Hz

2) HDMI 2.0a supports Ultra HD @ 60 Hz

3) D-Sub/VGA supports analog displays

Mainboard / BIOS

Shuttle Mainboard FS20

All capacitors are high quality solid capacitors

Supports resume after power failure [6]

Supports Wake on LAN (WOL)

Supports Power on by RTC Alarm

Supports boot from M.2 SSD cards und USB devices

AMI BIOS in 16 MByte EEPROM with SPI interface

Supports hardware monitoring and Watchdog function

Supports Unified Extensible Firmware Interface (UEFI)

Supports Firmware-TPM (fTPM) Version 2.0

Power Adapter

External 65 W power adapter (fanless)

Input: 100~240 V AC, 50/60 Hz, max. 1.6 A

Output: 19 V DC, max. 3.42 A, max. 65 W

DC cable length: ca. 170 cm

AC cable length: ca. 170 cm (3-pin Micky MM C6 and Schuko earthed safety plug)

DC Input connector

DC Input Connector: 5.5 / 2.5 mm (outer/inner diameter)

The DC-input of the computer supports an external

power source with either 12V±5% or 19V±5%.

Memory support

2x SO-DIMM slot with 260 pins

Supports DDR4-2666 (PC4-21300) SDRAM at 1.2 V

Supports DDR4-3200 at 2666 MHz

Supports Dual Channel mode

Supports a maximum of 32 GB per DIMM,

maximum total size: 64 GB

Supports two unbuffered DIMM modules (no ECC or registered)

2.5" Drive Bay with SATA connector

Supports one Serial ATA hard disk

or one SATA SSD drive in 6.35 cm / 2.5" format

Device height: max. 12.5 mm

Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth

Supports Unified Extensible Firmware Interface (UEFI)

Note: no Serial ATA cable is required.

M.2 Slot for SSDs

The M.2 2280 BM slot provides the following interfaces:

- PCI-Express Gen. 3.0 X4

- SATA v3.0 (max. 6 Gbps)

It supports M.2 cards with a width of 22 mm

and a length of 42, 60 or 80 mm (type 2242, 2260, 2280).

Supports M.2 SATA SSDs (with B+M key) and M.2 PCIe NVMe SSDs (with M key)

Supplied thermal pad for cooling M.2 SSDs.

M.2-2230E slot for WLAN cards

Interfaces: PCI-Express Gen. 2.0 X1 und USB 2.0

Supports M.2 cards with a width of 22 mm and a length of 30 mm (type 2230)

Supports WLAN expansion cards (optional Shuttle accessory: WLN-M / WLN-M1)

2x pre-installed antenna cables

Card Reader

Integrated SD card reader

Supports SD, SDHC and SDXC memory flash cards

Audio

Audio Realtek® ALC897 or ALC 662 High-Definition Audio

Two analog audio connectors (3.5 mm) at the front panel:

1) 2 channel line out (headphones)

2) microphone input

Digital multi-channel audio output: via HDMI and DisplayPort

Dual LAN (2.5G + 1G)

Dual network with two RJ45 ports

Used network chips:

1) left: Intel i211 Ethernet Controller supports 2.500 / 1.000 / 100 Mbps operation

2) right: Intel i219 Ethernet Controller supports 1.000 / 100 / 10 Mbps operation

Supports WAKE ON LAN (WOL)

Supports network boot by Preboot eXecution Environment (PXE)

Prepared for Wireless Network (WLAN)

2x pre-installed antenna cables (WLAN card and antennas not included)

Prepared for the installation of an M.2-2242 WLAN card and two external antennas

Front Panel connectors/buttons

2x USB 3.2 Gen 2 (red, max. 10 Gbps)

4x USB 2.0

Microphone input

Audio Line-out (headphones)

SD card reader (supports SD, SDHC, SDXC)

Power button

Power LED (blue)

HDD LED (yellow)

Back Panel connectors

DisplayPort 1.2 [3]

HDMI 2.0a

D-Sub/VGA

2x USB 3.2 Gen 2 (red, max. 10 Gbps)

2x Intel RJ45 LAN (left: 2.5 Gbps and right: 1 Gbps)

Serial COM port (5V / 12V, switchable to RS232 / RS422 / RS485) [1]

DC-input connector for external power adapter

4-pin connector (2.54 mm pitch) for power button, Clear CMOS and 5 V DC [4]

Always-On Jumper

By removing Jumper J9 (please refer to the quick user guide),

the system will start unconditionally once power is applied. [6]

Scope of Delivery

Multi-language user guide

Two metal feet with four screws M3 x 7 mm

VESA mount for 75/100mm standard (two metal brackets)

Four screws M3 x 7 mm (screws together VESA mount and PC)

Four screws M4 x 10 mm (to fix the VESA mount to the external surface)

Two screws M3 x 5 mm to mount a 2.5" storage in the bay

Two screws M3 x 5 mm to mount M.2 cards

Thermal pad for cooling M.2 SSDs

Driver DVD for Windows

External 65W power adapter with power cord (with protective-earth contacts)

Optional Accessories

- PCP11: adapter cable for the second COM port (replaces the VGA port)

- CXP01: adapter cable for external power button

- WWN03: LTE adapter kit for the 2.5" bay including two external LTE antennas [2]

- WLN-M / WLN-M1: WLAN module (supports WLAN/Bluetooth) with two external antennas and cables

- PRM01: 2U rack mount front plate for two Shuttle XPC slim

- DIR01: mounting kit for 35 mm DIN-Rail

Environmental Specifications

Operating temperature range: 0~40 °C [5]

Relative humidity, non-condensing: 10~90 %

Conformity & Certifications

EMI: CE, FCC, BSMI, RCM, VCCI

Safety: CB, BSMI, cTUVus

Other: RoHS, Energy Star, ErP

This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:

(1) 2014/30/EU relating to electromagnetic compatibility (EMC)

(2) 2014/35/EU relating to Electrical Equipment designed for use within certain voltage limits (LVD)

(3) 2009/125/EC relating to eco design requirements for energy-related products (ErP)

Footnote:

[1] Jumper for COM port configuration

Pin 9 of the COM-Port is a multi-functional signal. Based on the Jumper JP1 configuration on the mainboard, it can be configured as Ring Indicator (RI) or external power supply with a voltage level of either 5 V or 12 V. Each COM port can be configured separately. The operating mode of COM 1 can be set to RS232, RS422 or RS485 in the BIOS.

The second COM port (COM 2) supports RS232 mode only, and in the standard SKU of this product it is only available as an onboard connector on the mainboard. An appropriate adapter (e.g. the optional accessory PCP11) is required in order to provide this port as D-Sub connector at the back panel. In this case the VGA port cannot be used.

[2] LTE Adapter Kit WWN03

Using the LTE adapter kit WWN03 means, that the 2.5" bay can no longer be used for SATA drives in 2.5" format (hard disk or SSD). An SSD card in the M.2-2280 format must be used instead.

[3] How to convert DisplayPort into HDMI/DVI

The DisplayPort output can be converted to HDMI or DVI by an additional, passive adapter cable. For example:

DELOCK 82590: 1 m, DisplayPort (male, 20p) to HDMI-A (male, 19p)

DELOCK 82435: 5 m, DisplayPort (male, 20p) to DVI-D (male, 24p)

The integrated graphics automatically detects the connected display and puts out the appropriate electric signal - either through DisplayPort (without an adapter) or HDMI/DVI (with an adapter).

However, a monitor with a DisplayPort connector cannot be connected to the HDMI port with a simple, passive adapter.

[4] Four-pin header at the back panel

This header allows for connecting an external power button.

It also provides 5 V DC voltage for external devices and the Clear CMOS function. Optional accessory: the adapter cable CXP01.

[5] Caution: For ambient temperatures higher than 35 °C we strongly recommend to use an SSD instead of an HDD

[6] Power on after power fail:

The BIOS setup provides a "Power-On after Power Fail" function that can be found under "Power Management Configuration". This function determines the PC's behaviour after power failure. As a matter of the nature of this function, it may fail after short power failures. This is why this product also comes with a hardware-based solution. By removing Jumper J9 (please refer to the quick user guide), the system will start unconditionally once power is applied.

Artikelnummer:  SunPc-ET20V

                                       S P E C I F I C A T I E S 

ACCESSOIRES:

			CXP01 Cable for external push button switch Some B-Bit XPCs have a handy connector at the back panel to connect an external power button. In case the XPC is installed in a scenario where it cannot be accessed directly, be it VESA-mounted or otherwise remotely installed, it can still be powered on or off conveniently by using an external push button switch. B-Bit therefore provides a 2-metre cable with fitting connections that only requires a push button switch.
			Cable Shielded, industry-standard cable Length: ca. 2 metres Outer diameter: 6.5 mm Two-pole cable: 2x 0.34 mm² Colour: Black Connector Dual header connector, 2.54 mm pitch Two female crimp contact pins, tin-plated Required push button switch The cable provides tin-plated leads for a push button switch of your choice. The connection to the external power button can be screw-type or soldering. Compatibility The cable can be used with the following B-Bit XPC models: SunPC-ET10Vx

WLN-M

Wi-Fi expansion

SunPC-ET10Vx

WWN03

2.5“ adapter for 4G modules

SUNPC-ET10V, SUNPC-ET10V3, SUNPC-ET10V5, SUNPC-ET10V7